Orders placed after 2pm will ship the next business day.

Lat 26 UV Heat Guard

Lat 26 UV Heat Guard provides long lasting protection you can apply to your yacht or boat on a variety of surfaces including paint, gel coat, stainless steel, vinyl, leather, rubber, hypalon, Isinglass, and acrylic surfaces. This product takes minutes to apply to a clean and dry surface.

LAT-UVP1; LAT-UVP16

Date Prepared: 04/27/2017

Safety Data Sheet

Section 1. Identification Manufacturer:
Lat 26 ̊
205 SW 30
th Street

Fort Lauderdale, FL 33315 754-206-2356 – Office 954-588-4408 – 2nd contact

For Hazardous Materials [or Dangerous Goods] Incident Spill, Leak, Fire, Exposure, or Accident
Call CHEMTREC Day or Night
1-800-424-9300 / +1 703-527-3887 CCN815696

Product Identification: LAT 26 UV Protect/UV Heat Guard

Suggested Use: Use to remove minor imperfections and create a smooth polished finish on gel- coat, fiberglass, and painted surfaces.

Section 2. Hazard(s) Identification

Hazard Class &
Category Codes Hazard Statement Codes

Pictograms & Signal Word

Asp. Tox. 1 H304: May be fatal if swallowed and enters airways. Danger

Precautionary State- ments Codes

P101 P102

Precautionary Statements

If medical advice is needed, have product container or label at hand Keep out of reach of children

P103 Read label before use
P202 Do not handle until all safety precautions have been read and understood

P262 Do not get in eyes, on skin or on clothing

P301+311+315

P303+313
P404 Store in a closed container
P501 Dispose of contents/container to approved waste facility

IF SWALLOWED: Get immediate medical attention and call a POISON CENTER or doctor/physician

IF exposed or concerned: Get medical advice/attention

Section 3. Composition/Information on Ingredients

Component Name

Water
Isoparaffinic Hydrocarbon Amino-functional Polydimethylsiloxane

CAS Number

7732-18-5 64742-47-8 Proprietary

EC Number

231-791-2 265-149-8 N/A

Percentage

Balance 55-60% 22-25%

Section 4. First Aid Measures
Eyes: Flood with large amounts water at least 20 min.; get immediate medical attention if irritation per-

sists. Can cause irritation, redness, tearing, and blurred vision.
Skin: Flush exposed area with water. Remove all contaminated clothing. Prolonged or repeated con- tact can cause moderate irritation.
Inhalation: If affected, remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration. Keep person warm, calm, and get medical attention. Oral: If swallowed, induce vomiting. Vomiting can be induced with syrup of Ipecac. Give fluids until the vomitus is clear. Get medical attention.

Section 5. Fire Fighting Measures

Flash Point: 210°F
Autoignition Temperature: Not determined Flammability Limits in Air: Not determined

Extinguishing Media: Carbon dioxide (CO2) water spray. Dry chemical foam can be used to cool fire- exposed containers.
Fire Fighting Procedure: Self-contained breathing apparatus and protective clothing should be worn in fighting fires involving chemicals. Evacuate area in case of overheating or fire. Vapors are heavier than air and may travel to a source of ignition and flash back. Static electricity will accumulate and may ignite vapors.

Hazardous Decomposition Products: Carbon oxides and various hydrocarbons.

Section 6. Accidental Release Measures
Containment/Clean Up: Sections 13 and 15 of this MSDS provide information regarding certain Federal

and local requirements. Collect for disposal. Clean up remaining materials from spill with suitable ab- sorbent. For large spills provide diking or other appropriate containment to keep material from spread- ing. If diked material can be pumped, store recovered material in appropriate container. Clean area as appropriate as some silicone material, even in small quantities, may present a slip hazard. Final cleaning may require steam, solvents or detergents. Observe all personal protection equipment recommenda- tions described in Sections 5 and 8 of this MSDS. Observe all Federal and government regulations that may apply to the cleanup of this material.

Section 7: Handling and Storage
Handling (Personnel): Avoid contact with oxidizing agents. Spilled substance increases risk of slippage. Storage: Keep container tightly closed.

Section 8: Exposure Controls and Personal Protection Engineering Controls:

Local Exhaust: Provide sufficient mechanical (general and/or local exhaust) ventilation to main- tain exposure below TLV(s).

General exhaust: Recommended
Personal Protective Equipment for Routine Handling:

Eyes: Use proper protection – safety glasses as a minimum.
Skin: Washing at meal time and end of shift is adequate.
Suitable Gloves: butyl rubber protection gloves
Inhalation: If spraying or other operations that generate an aerosol mist are conducted, respira-

tory protection for exposed personnel is recommended. Precautionary Measures: Avoid eye contact.

Section 9: Physical and Chemical Properties:

Physical Form:

Color: Odor:

Viscous Liquid

Red Cherry

Viscosity:

Melting Point: Boiling Point:

Not determined

Not determined Not determined

Specific Gravity @ 25° C: 1.02 Solubility in Water: Soluble

VOC content (% by 8-12% weight)

Section 10: Stability and Reactivity Chemical Stability: Stable

Flash Point:
Vapor Pressure @ 25° C pH:

210° F
Not determined 6-7

Hazardous Polymerization: Will not polymerize
Conditions to Avoid: None known
Materials to Avoid: Strong oxidizing agents and strong acids.

Section 11: Toxicological Information

Acute Toxicity: Irritation to eyes and skin
Chronic: Unknown
Eyes: No data available
Skin: LD50, Rat: >2,000 mg/kg
Sensitization: Not a known sensitizer
Mutagenicity: No evidence for mutagenicity
Carcinogenicity: Contains no ingredients classified as carcinogens by NTP or OSHA

The following ingredients are classified as carcinogens by IARC: Petroleum Hydrocarbon
Light Mineral Oil

Reproductive Toxicity: No known reproductive toxicity Target Organs: None known
Aspiration Hazard: No data available

Section 12: Ecological Information

Fish: No data available Daphnia: No data available Algae: No data available

Section 13: Disposal Considerations

Landfill and/or incinerate where permitted in compliance with all applicable Federal, State and local gov- ernment regulations.

Section 14: Transportation Information DOT (US)
Not dangerous goods
IMDG

Not dangerous goods

IATA

Not dangerous goods

Section 15: Regulatory Information

Contents of this MSDS comply with the OSHA Hazard Communication Standard 29 CFR 1910.1200.

This product has been classified according to the hazard criteria of the CPR and the MSDS contains all the information required by the CPR.

TSCA Status:

EPA SARA Title III Chemi- cal Listings

All chemical substances in this material are included on or exempted from listing on the TSCA inventory of chemical substances.

Supplemental State Compliance Information

Section 16: Other Information

Section 302 Extremely Hazardous Substances

Section 304 CERCLA Hazardous Sub- stances

Section 312 Hazard Class

Section 313 Toxic Chemicals None

None

None

Acute No Chronic No Fire No Pressure No Reactive No None

The information accumulated herein is believed to be accurate but is not warranted to be whether origi- nating with the company or not. Recipients are advised to confirm in advance of need that the infor- mation is current, applicable, and suitable to their circumstances. Any material supplied is the sole re- sponsibility of the user. All materials may present unknown health hazards and we cannot guarantee that the hazards listed herein are the only hazards that exist.